Select a Mustang Generation
Air Intake Kit
Showing 1 – 10 products of 199 products
PMAS Cold Air Intake; Tune Required (11-14 Mustang GT 5.0L)
Vehicle | Submodel | CID |
---|---|---|
2011 Ford Mustang | GT | 302 |
2012 Ford Mustang | GT | 302 |
2013 Ford Mustang | GT | 302 |
2014 Ford Mustang | GT | 302 |
Vehicle | Submodel | CID |
---|---|---|
2011 Ford Mustang | GT | |
2012 Ford Mustang | GT | |
2013 Ford Mustang | GT | |
2014 Ford Mustang | GT |
PMAS Velocity Cold Air Intake | Tune Required (15-17 Mustang GT 5.0L)
More Air For More Power. Improve the power and performance of your Coyote powered S550 Mustang by replacing the restrictive factory intake with a PMAS Velocity Cold Air Intake. The stock air intake was not designed for the demands of a high performance muscle car, it was manufactured to meet the basic requirements of a mass produced commuter vehicle. It is just for this reason that PMAS engineered their Tune Required Velocity Intake to greatly improve air flow, when compared to stock, for a significant boost in rear wheel horsepower and torque. As an added bonus you will also experience a noticeable increase in idle, throttle response and over all engine performance.Calibration Required. Installation of this PMAS Velocity Cold Air Intake will require the use of a custom tune with a Handheld Tuner to reprogram the vehicles computer (ECU) for operation. By reprogramming your Mustangs ECU you will be able to realize the full power potential that this Cold Air Intake has to offer. Unique Design. Designed with maximum flow as the first priority, this PMAS Velocity Air Intake was engineered with computational fluid dynamic â??CFDâ? data for minimum restrictions. Featuring a patented mass air flow sensing system, this Cold Air Intake effectively uses a massive 120mm intake tube with no MAF resolution loss. The unique Velocity Stack inlet design maximizes airflow without turbulence for smooth, stable idle air flow which results in stock drivability. Reusable S&B Air Filter. The included high flow S&B Filter effectively filters out power robbing contaminants with its multi layer design. S&B Air Filters are made up of eight layers of specially treated cotton media that are mounted between two epoxy-coated wire screens. The red oil used to treat the cotton layers creates a sticky surface to capture harmful microscopic particles before they can enter your Mustang's engine. Seeing that the filter is reusable there is no need to buy a new filter every few thousand miles. You can just clean the filter, re-oil it, and reinstall - saving yourself money in the long haul. Straight Forward Installation. PMAS designed their Velocity Cold Air Intake kit to easily install in under an hour. Installation can be completed with just basic hand tools, no extra modifications or special tools are required. All necessary hardware and instructions are included. Application. This PMAS Velocity Cold Air Intake System is specifically designed to fit the 2015-2017 GT Mustangs equipped with the 5.0L Coyote V8 engine and requires re-tuning of the vehicles computer for operation. Technical Note. This product is not legal for use in California or any other state adopting California emission standards. Not legal for use on pollution controlled motor vehicles; intended for off road use only. Fitment: 2015 Ford Mustang 2016 Ford Mustang 2017 Ford Mustang Details PMAS N-MT13-1 CA Residents: WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov
Vehicle | Submodel | CID |
---|---|---|
2015 Ford Mustang | GT | 302 |
2016 Ford Mustang | GT | 302 |
2017 Ford Mustang | GT | 302 |
Vehicle | Submodel | CID |
---|---|---|
2015 Ford Mustang | GT | |
2016 Ford Mustang | GT | |
2017 Ford Mustang | GT |
PMAS Cold Air Intake; Tune Required (18-21 Mustang GT 5.0L)
Enhance Performance. Give your Mustang GT the performance it deserves with the PMAS Tune Required Cold Air Intake. With its large, velocity stack design 120-mm inlet tube, this cold air intake is engineered to provide your engine with more than enough cold air. This increased supply of cold air results in a more complete fuel combustion, a quicker throttle response, and improved horsepower and torque. ECU Re-Tune Necessary. The PMAS Tune Required Cold Air Intake requires a re-tune of your ECU. The larger diameter inlet tubes may cause a check engine light, due to the larger amount of air entering your system. Moreover, an ECU re-tune will maximize the performance potential of this cold air intake. Easy To Clean Air Filter. The high-performance air filter that comes with the PMAS Tune Required Cold Air Intake is designed to maximize airflow entering your engine without compromising filtration. This is achieved through its conical shape and â??openâ? style. This air filter is also designed to be easy to clean, so you donâ??t have to replace it every so often. Rugged Construction. The PMAS Tune Required Cold Air Intakeâ??s large air inlet tube is constructed from features an injection-molded thermoplastic that can take engine bay heat without failing. This air intake comes with a heat shield thatâ??s crafted from high-grade aluminum to protect the air filter from heat damage, extending its service life. This heat shield receives a tough black powder-coat finish, giving it excellent corrosion protection. Durable Injection-Molded MAF Housing Included. The PMAS Tune Required Cold Air Intake includes a MAF housing thatâ??s crafted from injection-molded thermoplastic. This MAF sensor can accommodate your Mustangâ??s MAF sensor without modifications. Simple Bolt-On, No Mod Installation. The PMAS Tune Required Cold Air Intake bolts on to your Mustangâ??s factory air system location without the need for modifications. Installation is completed using just standard hand tools. Covered by a 90-Day Limited Warranty. The PMAS Tune Required Cold Air Intake is covered by a 90-day limited warranty against manufacturing defects. Please visit the manufacturerâ??s website for more details. Not CARB-Certified. The PMAS Tune Required Cold Air Intake is not CARB-certified at this time, making its use illegal in states that have adopted CARB certification. Please check local laws for applications where this cold air intake is permitted. Application. The PMAS Tune Required Cold Air Intake fits all 2018-2021 Ford Mustang GT models. Fitment: 2018 Ford Mustang 2019 Ford Mustang 2020 Ford Mustang 2021 Ford Mustang Details: PMAS N-MT14-1 CA Residents: WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov
Vehicle | Submodel | CID |
---|---|---|
2018 Ford Mustang | GT | 302 |
2019 Ford Mustang | GT | 302 |
2020 Ford Mustang | GT | 302 |
2021 Ford Mustang | GT | 302 |
Vehicle | Submodel | CID |
---|---|---|
2018 Ford Mustang | GT | |
2019 Ford Mustang | GT | |
2020 Ford Mustang | GT | |
2021 Ford Mustang | GT |
JLT Cold Air Intake with Red Oiled Filter; Tune Required (18-23 Mustang GT)
Perfect Alignment. Whether your Foxbody stretches its legs on the street, the strip, or at the track, you need a good alignment. The adjustability these caster/camber plates offer will make lining things up easy and worry-free.
Vehicle | Submodel | CID |
---|---|---|
2018 Ford Mustang | GT | 302 |
2019 Ford Mustang | GT | 302 |
2020 Ford Mustang | GT | 302 |
2021 Ford Mustang | GT | 302 |
2022 Ford Mustang | GT | 302 |
Vehicle | Submodel | CID |
---|---|---|
2018 Ford Mustang | GT | |
2019 Ford Mustang | GT | |
2020 Ford Mustang | GT | |
2021 Ford Mustang | GT | |
2022 Ford Mustang | GT | |
2023 Ford Mustang | GT |
JLT Cold Air Intake with Red Oiled Filter; Tune Required (15-17 Mustang GT)
JLT Cold Air Intake with Red Oiled Filter - Tuned Required (15-17 Mustang GT) CAI-FMG-15
Description More Usable Horsepower. With a JLT Performance Cold Air Intake and a custom tune installed on your 2015-2017 GT you can expect to see a huge jump in horsepower and torque at the rear wheels. The cold air intake itself is good for 15 RWHP and 12 RWTQ, but when combined with the required tune you can expect to see up to an additional 37 horsepower and 26 ft/lbs. of torque at the rear wheels over stock. In addition to an increase in power you will also see an impressive improvement in driving performance. 110mm MAF Housing. This JLT Cold Air Intake Kit has a unique design that incorporates a 110mm MAF housing right into the tube for a clean factory appearance (MAF not included). Heat Shield Included. The JLT Performance Cold Air Intake includes a roto molded ABS plastic heat shield that not only looks great, but blocks out excessive under hood engine heat at low speed and idle that can rob you of power. Money Saving Reusable Filter. This JLT Cold Air Intake kit comes complete with a high flow reusable S&B brand oiled air filter. So that means there is no need to go out and buy a new filter every few thousand miles. Now you can just clean the filter, re-oil it, save money, and go! Required Upgrade. Installation of this Cold Air Intake will require the use of a Mustang Handheld Tuner to reprogram the vehicles computer (ECU) for operation or a custom Lund Racing tune. Contact us for details. Application. This JLT Cold Air Intake is specifically designed for use on the 2015-2017 5.0 GT Mustang with either a manual or automatic transmission. Requires a new computer tune. Fitment: 2015 Ford Mustang - 2016 Ford Mustang - 2017 Ford Mustang
Vehicle | Submodel | CID |
---|---|---|
2015 Ford Mustang | GT | |
2016 Ford Mustang | GT | |
2017 Ford Mustang | GT |
Vehicle | Submodel | CID |
---|---|---|
2015 Ford Mustang | GT | 302 |
2016 Ford Mustang | GT | 302 |
2017 Ford Mustang | GT | 302 |
Performance Air Intake System - Air Intake Kit - K&N
Filtercharger Injection Performance Kit
Performance Air Intake System
Includes Air Filter/Heat Shield/Tubing; Estimated Horsepower Gain 7.54 HP At 4966 RPM;CARB E.O. D-269-37
K/N s roto-molded cold air intake systems are guaranteed to provide an increase in horsepower and torque; and are protected by the K/N No-Hassle Lifetime Limited Warranty.
- Air Box Included: No
- Air Filter Element Washable: Yes
- Air Filter Height: 6.000 In. (152mm)
- Air Filter Large End Diameter: 7.500 In. (191mm)
- Air Filter Outlet Length: 6.000 In. (152mm)
- Air Filter Outlet Shape: Round
- Air Filter Outlet Width: 6.000 In. (152mm)
- Clamp Color: Natural
- Clamp Material: Stainless Steel
- Clamp Quantity: 5
- Clamp Style: Regular
- Coupler Color: Black
- Couplers Included: 2
- Estimated Horse Power Gain: 7.54 Hp @ 4996 Rpm
- Filter Color: Red
- Filter Material: Cotton Gauze
- Horse Power Increase: 8 Hp
- Intake Pipe Color: Black
- Intake Pipe Material: High-density Cross-linked Polyethylene
- Item Weight: 8.800 Lbs. (4 Kg)
- Mass Air Flow Sensor Included: Mass Air Flow Sensor Adapter Included When Required
- Mounting Hardware Included: Yes
- Oil Included: Filter Is Pre-oiled
- Package Material: Paperboard
- Package Type: Box
- Product Box Height: 12.500 In. (318mm)
- Product Box Length: 22.250 In. (565mm)
- Product Box Width: 14.250 In. (362 Mm)
- Prop 65 (C, R or CR): Cr
- Prop 65 Warning Label: Https://www.knfilters.com/images/l/prop65.jpg
- Replacement Filter: Rf-1048
- RPM: 4996
- Street Legal: Yes
- TUV Approved (Europe): No
- WARNING CA Proposition 65: Yes
- WARNING CA Proposition 65 Message: Warning: Cancer And Reproductive Harm - Www.p65warnings.ca.gov
-
Features:
- Guaranteed To Increase Horsepower
- Designed To Improve Throttle Response And Engine Sound
- Washable And Reusable Lifetime Air Filter
- Easy To Install Usually In 90 Minutes or Less
- Replaces Entire Factory Air Intake System
- K&N Million Mile Limited Warranty
Vehicle | Submodel | Block | Engine | CID | CC |
---|---|---|---|---|---|
2005 Ford Mustang | Base | V | 6 Cyl 4.0L | 245 | - |
2006 Ford Mustang | Base | V | 6 Cyl 4.0L | 245 | - |
2007 Ford Mustang | Base | V | 6 Cyl 4.0L | 245 | - |
2008 Ford Mustang | Base | V | 6 Cyl 4.0L | 245 | - |
2009 Ford Mustang | Base | V | 6 Cyl 4.0L | 245 | - |
Performance Air Intake System - Air Intake Kit - K&N
Filtercharger Injection Performance Kit
Performance Air Intake System
Includes Air Filter/Heat Shield/Tubing; Estimated Horsepower Gain 59.96 HP At 5900 RPM;CARB E.O. D-269-37
K/N s roto-molded cold air intake systems are guaranteed to provide an increase in horsepower and torque; and are protected by the K/N No-Hassle Lifetime Limited Warranty.
- Air Box Included: No
- Air Filter Element Washable: Yes
- Air Filter Height: 6.000 In. (152mm)
- Air Filter Large End Diameter: 7.500 In. (191mm)
- Air Filter Outlet Length: 6.000 In. (152mm)
- Air Filter Outlet Shape: Round
- Air Filter Outlet Width: 6.000 In. (152mm)
- Clamp Color: Natural
- Clamp Material: Stainless Steel
- Clamp Quantity: 5
- Clamp Style: Regular
- Coupler Color: Black
- Couplers Included: 2
- Estimated Horse Power Gain: 56.96 Hp @ 5900 Rpm
- Filter Color: Red
- Filter Material: Cotton Gauze
- Horse Power Increase: 57 Hp
- Intake Pipe Color: Black
- Intake Pipe Material: High-density Cross-linked Polyethylene
- Item Weight: 9.000 Lbs. (4.1 Kg)
- Mass Air Flow Sensor Included: Mass Air Flow Sensor Adapter Included When Required
- Mounting Hardware Included: Yes
- Oil Included: Filter Is Pre-oiled
- Package Material: Paperboard
- Package Type: Box
- Product Box Height: 12.500 In. (318mm)
- Product Box Length: 22.250 In. (565mm)
- Product Box Width: 14.250 In. (362 Mm)
- Prop 65 (C, R or CR): Cr
- Prop 65 Warning Label: Https://www.knfilters.com/images/l/prop65.jpg
- Replacement Filter: Rf-1048
- RPM: 5900
- Street Legal: Yes
- TUV Approved (Europe): No
- WARNING CA Proposition 65: Yes
- WARNING CA Proposition 65 Message: Warning: Cancer And Reproductive Harm - Www.p65warnings.ca.gov
-
Features:
- Guaranteed To Increase Horsepower
- Designed To Improve Throttle Response And Engine Sound
- Washable And Reusable Lifetime Air Filter
- Easy To Install Usually In 90 Minutes or Less
- Replaces Entire Factory Air Intake System
- K&N Million Mile Limited Warranty
Vehicle | Submodel | Block | Engine | CID | CC |
---|---|---|---|---|---|
2007 Ford Mustang | Shelby GT500 | V | 8 Cyl 5.4L | 330 | - |
2008 Ford Mustang | Shelby GT500 | V | 8 Cyl 5.4L | 330 | - |
2008 Ford Mustang | Shelby GT500KR | V | 8 Cyl 5.4L | 330 | - |
2009 Ford Mustang | Shelby GT500 | V | 8 Cyl 5.4L | 330 | - |
2009 Ford Mustang | Shelby GT500KR | V | 8 Cyl 5.4L | 330 | - |
Performance Air Intake System - Air Intake Kit - K&N
Typhoon Short Ram Cold Air Induction Kit
Performance Air Intake System
Includes Red Air Filter/Polished Tubing/Heat Shield; Estimated Horsepower Gain 7.07 HP At 5200 RPM;CARB E.O. D-269-37
K/N s mandrel-bent aluminum cold air intake systems are guaranteed to provide an increase in horsepower and torque; and are protected by the K/N No-Hassle Lifetime Limited Warranty.
- Air Box Included: No
- Air Filter Element Washable: Yes
- Air Filter Height: 6.000 In. (152mm)
- Air Filter Large End Diameter: 7.500 In. (191mm)
- Air Filter Outlet Length: 6.000 In. (152mm)
- Air Filter Outlet Shape: Round
- Air Filter Outlet Width: 6.000 In. (152mm)
- Clamp Color: Natural
- Clamp Material: Stainless Steel
- Clamp Quantity: 5
- Clamp Style: Regular
- Coupler Color: Black
- Couplers Included: 2
- Estimated Horse Power Gain: 7.07 Hp @ 5200 Rpm
- Filter Color: Red
- Filter Material: Cotton Gauze
- Horse Power Increase: 7 Hp
- Intake Pipe Color: Polished
- Intake Pipe Inlet Length: 21.500 In. (546mm)
- Intake Pipe Inlet Shape: Round
- Intake Pipe Inlet Width: 2.750 In. (70mm)
- Intake Pipe Material: Aluminum
- Intake Pipe Outlet Length: 21.500 In. (546mm)
- Intake Pipe Outlet Shape: Round
- Intake Pipe Outlet Width: 2.750 In. (70mm)
- Item Weight: 9.700 Lbs. (4.4 Kg)
- Mass Air Flow Sensor Included: Mass Air Flow Sensor Adapter Included When Required
- Mounting Hardware Included: Yes
- Oil Included: Filter Is Pre-oiled
- Package Material: Paperboard
- Package Type: Box
- Prop 65 (C, R or CR): Cr
- Prop 65 Warning Label: Https://www.knfilters.com/images/l/prop65.jpg
- Replacement Filter: Rf-1048
- RPM: 5200
- Street Legal: Yes
- System Type: Cold Air
- TUV Approved (Europe): No
- WARNING CA Proposition 65: Yes
- WARNING CA Proposition 65 Message: Warning: Cancer And Reproductive Harm - Www.p65warnings.ca.gov
-
Features:
- Guaranteed To Increase Horsepower
- Designed To Improve Throttle Response And Engine Sound
- Free Flowing Aluminum Tube
- Easy To Install Usually In 90 Minutes or Less
- Lasts Up To 100000 Miles Before Service Is Required
- Replaces Entire Factory Air Intake System
- Washable And Reusable Lifetime Air Filter
- K&N Million Mile Limited Warranty
Vehicle | Submodel | Block | Engine | CID | CC |
---|---|---|---|---|---|
2005 Ford Mustang | Base | V | 6 Cyl 4.0L | 245 | - |
2006 Ford Mustang | Base | V | 6 Cyl 4.0L | 245 | - |
2007 Ford Mustang | Base | V | 6 Cyl 4.0L | 245 | - |
2008 Ford Mustang | Base | V | 6 Cyl 4.0L | 245 | - |
2009 Ford Mustang | Base | V | 6 Cyl 4.0L | 245 | - |
Performance Air Intake System - Air Intake Kit - Airaid
AIRAID MXP Series Cold Air Intake System
Performance Air Intake System
Includes SynthaMax Dry Red Air Filter/Airbox/Intake Tube/Velocity Stack/Hardware;CARB E.O. D-609-15
The AIRAID MXP Air Intake System represents the ultimate in AIRAID s cold air induction systems and delivers higher levels of horsepower and acceleration gains for high-performance gas and diesel vehicles.
- Prop 65 (C, R or CR): Cr
- Prop 65 Warning Label: Https://www.knfilters.com/images/l/prop65.jpg
- WARNING CA Proposition 65: Yes
- WARNING CA Proposition 65 Message: Warning: Cancer And Reproductive Harm - Www.p65warnings.ca.gov
- Clamp Color: Natural
- Clamp Quantity: 3
- Clamp Style: Worm Gear
- Filter Material: Non-woven Synthetic
- Intake Pipe Material: High-density Cross-linked Polyethylene
- Item Weight: 10.200 Lbs. (4.6 Kg)
- Mass Air Flow Sensor Included: Mass Air Flow Sensor Adapter Included When Required
- Oil Included: No Filter Oil Required
- Package Material: Paperboard
- Package Type: Box
- Product Box Height: 15.600 In. (396mm)
- Product Box Length: 19.900 In. (505mm)
- Replacement Filter: 701-458
-
Features:
- Superior Horsepower And Acceleration Gains
- Replaces Stock Air Box/Air Filter/Intake Tubing
- Easy To Install Using Common Available Tools
- High Airflow Premium Air Filter Media
- Washable And Reusable Air Filter Media
- No Hassle Lifetime Warranty
Vehicle | Submodel | Block | Engine | CID | CC |
---|---|---|---|---|---|
2011 Ford Mustang | Base | V | 6 Cyl 3.7L | 227 | 3726 |
2012 Ford Mustang | Base | V | 6 Cyl 3.7L | 227 | 3726 |
2013 Ford Mustang | Base | V | 6 Cyl 3.7L | 227 | 3726 |
2014 Ford Mustang | Base | V | 6 Cyl 3.7L | 227 | 3726 |
Vehicle | Submodel | Block | Engine | CID | CC |
---|---|---|---|---|---|
2012 Ford Mustang | Base | V | 6 Cyl 3.7L | 227 | 3726 |
2014 Ford Mustang | Base | V | 6 Cyl 3.7L | 227 | 3726 |
2013 Ford Mustang | Base | V | 6 Cyl 3.7L | 227 | 3726 |
2011 Ford Mustang | Base | V | 6 Cyl 3.7L | 227 | 3726 |
Performance Air Intake System - Air Intake Kit - Airaid
AIRAID MXP Series Cold Air Intake System
Performance Air Intake System
Round; Includes Blue Non-Woven Synthetic Filter/Airbox/Hardware; Estimated Horse Power Gain 8.11 HP At 5003 RPM;CARB E.O. D-609-18
AIRAID MXP Air Intake Systems represent the ultimate in AIRAID cold air induction systems and provide higher levels of horsepower and acceleration gains for high-performance gas and diesel vehicles.
- Clamp Color: Natural
- Clamp Quantity: 4
- Clamp Style: Worm Gear
- Estimated Horse Power Gain: 8.11 Hp @ 5003 Rpm
- Filter Material: Non-woven Synthetic
- Intake Pipe Material: High-density Cross-linked Polyethylene
- Item Weight: 8.000 Lbs. (3.6 Kg)
- Oil Included: No Filter Oil Required
- Package Material: Paperboard
- Package Type: Box
- Product Box Height: 12.500 In. (318mm)
- Product Box Length: 16.000 In. (406mm)
- Prop 65 (C, R or CR): Cr
- Prop 65 Warning Label: Https://www.knfilters.com/images/l/prop65.jpg
- Replacement Filter: 703-462
- WARNING CA Proposition 65: Yes
- WARNING CA Proposition 65 Message: Warning: Cancer And Reproductive Harm - Www.p65warnings.ca.gov
-
Features:
- Superior Horsepower And Acceleration Gains
- Replaces Stock Air Box/Air Filter/Intake Tubing
- Easy To Install Using Common Available Tools
- High Airflow Premium Air Filter Media
- Washable And Reusable Air Filter Media
- No Hassle Lifetime Warranty
Vehicle | Submodel | Aspiration | Engine VIN | Block | Engine | CID | CC | Fuel Type | Fuel Delivery Type |
---|---|---|---|---|---|---|---|---|---|
1999 Ford Mustang | GT | X | V | 8 Cyl 4.6L | 281 | - | |||
2003 Ford Mustang | GT | Naturally Aspirated | X | V | 8 Cyl 4.6L | 281 | - | ||
2000 Ford Mustang | GT | V | 8 Cyl 4.6L | 281 | - | ||||
2002 Ford Mustang | GT | V | 8 Cyl 4.6L | 281 | - | ||||
2004 Ford Mustang | GT | Naturally Aspirated | X | V | 8 Cyl 4.6L | 281 | - | ||
2001 Ford Mustang | GT | X | V | 8 Cyl 4.6L | 281 | - |
Vehicle | Submodel | Aspiration | Engine VIN | Block | Engine | CID | CC | Fuel Type | Fuel Delivery Type |
---|---|---|---|---|---|---|---|---|---|
2000 Ford Mustang | GT | V | 8 Cyl 4.6L | 281 | - | ||||
2001 Ford Mustang | GT | X | V | 8 Cyl 4.6L | 281 | - | |||
2002 Ford Mustang | GT | V | 8 Cyl 4.6L | 281 | - | ||||
2004 Ford Mustang | GT | Naturally Aspirated | X | V | 8 Cyl 4.6L | 281 | - | ||
2004 Ford Mustang | GT Equipado | Naturally Aspirated | X | V | 8 Cyl 4.6L | 281 | - | GAS | FI |
Showing 1 – 10 products of 199 products